Digital transformation of factory workshop Hardware Electric meter Sensor

As a professional provider of IoT data acquisition solutions and an expert in industrial IoT data acquisition, the editor of Shanghai Data Acquisition IOT Technology Co., Ltd， (daq-iot) hereby presents the following introduction, and sincerely welcomes discussions and exchanges. Supported Communication Interfaces: CAN, RS485, Mbus, 4–20mA, Profibus, CC-Link, HART, digital I/O, etc. Industrial Protocols: Modbus RTU/TCP, HJ212, IEC104, DLT645, DLMS, IEC61850, MQTT, etc. Mail:export@daq-iot.com

Wired multifunctional electric meter for full power measurement and electric pascal measurement, supporting 1-channel x and current+4-channel temperature 3di+2do, supporting RS-485 4G 2-31 time waveform measurement, voltage transient detection, time-sharing billing, demand calculation, xxxx timing recording, and other equipmentsupercapacitor Support proactive uploading of power outage events

Wireless function electric meter for full power measurement and energy measurement, supporting 1 x and 4 current channels, temperature 3di+2do, RS-485 4G 2-31 time waveform measurement, voltage transient detection, time-sharing billing, demand calculation, xxxx timing recording, etc. Equipped with supercapacitors to support active uploading of power outage events

Current transformer input 5A output 40mA accuracy level 0.5 working temperature -10 ° C -+50 ° C

Water meter diameter DN15-DN200 communication method 4G wireless battery power supply not less than 5 years working pressure ＜ 1.6mpa temperature range 0.1 ° -50 ° installation method horizontal pressure loss ≤ 0.063mpa

Thermal meter communication method 4G wireless caliber DN65-DN150 measurement range 0.1-1000m ³/h accuracy level ± 1.0 working pressure ≤ 1.6mpa protection levelIP68

The gas meter Data Acquisition meets the installation requirements of xx meter reading system protection level IP68, working temperature -40 ° C~70 ° C, and power supply mode Lithium batteryPower supply battery capacity 8000mAh standby power consumption less than 3 μ A transmission method 4G anti-theft device terminal removed Real-time alarm button meter reading support manual button Real-time meter reading infrared meter reading and intelligent xx infrared communication including one-year platform fee and data fee

Passive wireless temperature measurement Sensor measurement range -40 °~+125 ° accuracy ± 1 ° temperature measurement accuracy ± 2% RH

Active wireless temperature measurement Sensor measurement range -40 °~+125 ° accuracy ± 1 ° temperature measurement accuracy ± 2% RH

Water immersion Sensor DC12V/2A range DC9-18V

Smoke Sensor RS485 10~30VDC

Data Acquisition Module Data Acquisition Device 1. (1 Road Network Port 2 RS485 8 10 Input Supports Data Interchange with xx xx) (50 pieces) Data Acquisition Device 2 Equipped with RS485 xx interface, supporting no less than 8 environmental monitoring channels Sensor Data Acquisition, capable of data forwarding, able to access environmental data support networks such as COO, hydrogen SO2, etc. Protocol, IP TCP ARP ICMP DHCP DKS, working temperature -30 ° C~+85 ° C, power supply 9-24V (15)

Acceleration Sensor (including armored extension cable) Response range 0.1Hz-10KHz (± 3dB) Sensitivity 4.00MV/m/s Impact resistance ± 5000g Operating temperature 40 °~+121 ° Protection level IP68 Explosion proof level Ex ia IIC T6

Dynamic pressure Sensor (including armored extension cable) Range 0-80mpa Output 4-20mA Response time ≤ 1ms Protection level IP67 Explosion proof level Ex ia IIC T6

The edge Data Acquisition unit (three cylinder drilling pump) can receive key addition, speed, vibration, pressure, temperature, and other Sensor signals to synchronously collect all signals, ensuring that there is no corresponding difference in the original waveform between channelsEdge ComputingThe intelligent analysis function supports a minimum of 16 monitoring channels for the power and hydraulic ends of the three cylinder pump. The sample length of xxx data is ≥ I63B4, and the frequency analysis rate △ I ≤ xxx angle or upper x angle analysis rate is ≤ 1. The overall accuracy error of the system is ≤ 1%

The edge Data Acquisition unit (five cylinder drilling pump) can receive signals such as key addition, speed, vibration, pressure, temperature, etc. Sensor to synchronously collect all signals, ensuring that there is no corresponding difference in the original waveform between channels. It has Edge Computing and intelligent analysis functions. It supports monitoring channels for the power and hydraulic ends of the five cylinder pump, with a minimum of 24 channels. The data sample length is ≥ I63B4. The frequency analysis rate △ I ≤ xxx angle or upper x angle analysis rate ≤ 1. The overall accuracy error of the Data Acquisition system is ≤ 1%